Coil Base Adapter

Coil Base Adapter: This plate is designed to adapt the 86-87 CCCI module and coil to the 84-85 engines.  Adapter bolts in place and allows the footprint of the 3 bolt 86-87 style coil  module to fit into the 4 bolt 85 style mounting.  All mounting  hardware is included.   

Coil Base Adapter.....$29.00

Fuel Pump Wiring Upgrade

Fuel Pump Wiring Upgrade: By far the finest "hotwire" kit on the market, this "plug-n-play" system uses a sealed 30 amp relay and sealed connectors.  Also included is an inline fuse and all necessary hardware needed to install this kit.  This kit will increase the voltage to your fuel pump by about 2 volts. 

Fuel Pump Upgrade.....$55.00

CCCI Module Converter

CCCI Module Converter: The 1984-1985 coil module is headed for obsolescence and is VERY expensive to replace.  This converter allows you to use the 86-87 coil on an 84-85 car.  Order the Coil Base Adapter (108085) and Ignition Module (107125) separately to complete installation. 

CCCI Module Converter.....$55.00

Billet Vacuum Pod

Billet Vacuum Pod: This Billet Vacuum Pod will replace the plastic factory vacuum distribution block on your 84-85 Turbo engine. This item is identical in fit to the factory plastic block except it is made of aluminum and is warp-proof.  

Billet Vacuum Pod.....$35.00

Heated Oxygen Sensor Kit

Heated Oxygen Sensor: Heated oxygen sensors are used on nearly all production cars since the early 1990's.  This kit allows you to add a heated oxygen sensor to your Turbo Buick without cutting or splicing wires.  Heated oxygen sensors become active much faster than non-heated and they are also more resistant to lead contamination than non-heated sensors. Kit comes with one sensor and harness.  

Heated Oxygen Sensor Kit.....$79.00

Fan Relay Kit

Fan Relay Kit: The 1984-1985 turbo Buicks did not have an electric fan.  This fan kit makes it easy to add an electric fan to the 84-85 cars and maintain ECM control over temperature.  Kit includes automotive spec sealed relay and all wiring needed.  Requires coolant fan, MAT kit below, MAT sensor  and upgrade of ECM and EPROM to complete installation.   

Fan Relay Kit.....$65.00

MAT Installation Kit

MAT Installation Kit: This kit is specially designed to allow the addition of a MAT sensor into pre-1986 Turbo Regals.  the use of a MAT sensor then allows the use of the 87 style ECM into the 84-85 cars.  Kit does not include MAT sensor. Order MAT sensor (109025) separately to complete installation.    

MAT Installation Kit.....$29.00

Manifold Air Temp Sensor

Manifold Air Temperature Sensor: This MAT (Manifold Air Temperature) sensor can be located in the collar of your K&N filter and provides inlet air temperature information to the ECM in order to scale your air/fuel parameters.  The sensor we supply can easily be placed in the air filter by drilling a 3/8" hole and pressing the MAT sensor into the drilled hole. Also referred to as IAT (Inlet Air Temperature) sensor.

Manifold Air Temp Sensor.....$12.00

TPS-TEC Throttle Enhancer

TPS-TEC Throttle Enhancer:  The Throttle Position Enhancer is designed to optimize the throttle signal send to the ECM at 70% throttle.  This unit will ensure maximum programmed ECM performance via fuel delivery and spark timing.  Corrects for any flat spots or dead spots in the throttle sensor and maintains 100% power enrichment at wide-open-throttle operation. 

TPS-TEC Throttle Enhancer.....$89.95

Negative Battery Cable

Negative Battery Cable: Replace your cracked, burned, or damaged negative battery cable with our newly designed cable.  This cable comes complete with the secondary ground lug and protector cap. 

Negative Battery Cable.....$30.00

Race and Street EPROMS

Race and Street EPROM's: Our custom EPROM chips are available for any octane, injector size and turbo combination up to 55 lb. injectors.  We custom program fuel, turbo boost, spark recovery, idle parameters, torque converter lockup, ignition timing, spark attack rate, rev and MPH limits, cruise A/F, coolant fan operation, and several other parameters on your 1984-1987 turbo Regal, GN, GNX,  1989 turbo Pontiac Trans-Am.CALL FOR APPLICATION

Race and Street EPROMS.....$69.00

Detail Tape

Detail Tape:  This tape is manufactured specifically for the engine wiring harness.  It is heat resistant and does not shrink under the extreme temperatures found under the hood.  One roll is enough to re-tape an entire engine harness twice.

Detail Tape.....$8.00

Injector Harness

Injector Harness:  Our fuel injector harness is produced to OEM specification using Packard connectors and factory cross linked wire.  Each injector connector is numbered for ease of installation.  Designed for 1984-1985 turbo engines. 

Injector Harness.....$89.00

Engine Wiring Harness

Complete Engine Harness:  Our engine harness is designed to better-than factory specifications.  This complete plug in harness is used for the 1984-1985 Turbo Regals and is made with OEM connectors and wiring. Race and Dyno harness available.

Engine Wiring Harness.....$625.00

Positive Battery Cable

Positive Battery Cable: The factory battery positive cable is obsolete.  We manufacture ours to factory specifications except we make our slightly longer so that it won't interfere with aftermarket  down-pipes, reducing a major cause of failure.  Fitted with protective cap. 

Positive Battery Cable.....$75.00

Detail Kit

Detail Kit 1984-1985:  This detail kit includes 1 roll of detail tape, mounting clips, and various sized wire conduit.  There is enough conduit included in the kit to detail an entire engine compartment.   

Detail Kit.....$39.00